high temperature tempering
英 [haɪ ˈtemprətʃə(r) ˈtempərɪŋ]
美 [haɪ ˈtemprətʃər ˈtempərɪŋ]
网络 高溫回火; 高温回火
双语例句
- Based on these, according to characteristic of steel tempering structure, high temperature tempering structure of hull steel is called tempered martensite.
认为，根据各种回火组织的特性，船体钢的高温回火组织应归为回火索氏体。 - Quenching and High Temperature Tempering Process of Special Cartridge Discus
特种弹弹壳圆饼调质热处理 - New Type High Temperature Electric Heating Salt-Bath Tempering Furnace
新型电加热管式高温盐浴回火炉 - The lower the deformation temperature, the finer the carbide, and the more uniform the distribution, therefore, the higher the strength and toughness after high temperature tempering.
形变温度愈低，回火时析出的碳化物愈细、分布愈均匀。 - The microstructures and properties of axles quenched after wedge cross rolling and high temperature tempered by induction tempering are investigated.
研究了轴类零件楔横轧后，利用轧后余热淬火和感应加热快速高温回火后的显微组织及主要性能； - The high temperature tempering mechanism due to quich induction heating has been analysed.
分析了快速调质工艺的高温回火机制。 - The results indicate that ultra-fine spheroidized carbides were formed by complete austenizing with high temperature tempering, and ultra-fine martensite or pearlite could be formed when the steel was then heated to lower austenizing temperature and quenched or normalized.
试验表明，该钢完全奥氏体化淬火后通过高温回火得到大量超细球状碳化物，然后在低温奥氏体化进行二次淬火和正火，获得超细马氏体、珠光体。 - The low cycle fatigue property of surface quenching grade C steel is higher than that of normalization grade C steel and quenching and high temperature tempering grade C steel.
表面淬火C级钢比调质C级钢和正火C级钢的低周疲劳性能高，在应变量较大时，调质C级钢和正火C级钢低周疲劳寿命较高； - The velocity in normalizing structure is between the velocity in medium temperature and high temperature tempering production after quenching.
正火组织的C1介于淬火后中温回火及高温回火产物组织的C1之间。 - The Microstructure and Properties or Wedge Cross-rolled Quenching and Fast High Temperature Tempering for Axles
轴件轧后的余热淬火及快速回火后的组织性能 - The tempering embrittlement will also be produced by holding at 380 ℃ under the known temperature range of the high temperature tempering embrittlement.
在公认的高温回火脆性温度范围以下380℃保温，同样产生脆化。 - For alloy construction steel with quench and high temperature tempering, heat treatment technique with getting Ultra fine prior austenite grain size, increase of hydrogen traps and interface strength are combined;
采用调质处理的合金结构钢，应用新的合金设计思路以提高界面温度，增加氢陷阱和二次硬化路线，快速超细晶热处理的综合技术； - The results shown that the quich induction quenching and high temperature tempering by using series inductors can obviously increase the strength and toughness and tensile fatigue servies life of the oil pump arm, remarkably enhance production efficiency and considerably economize electrical power.
结果表明：串联感应加热快速调质能明显提高抽油杆的强韧性和拉伸疲劳抗力，显著地提高生产效率并大量节约能源。 - The carbide type and its dissolution process in microstructure of 718 plastic die steel were analyzed by TEM analyses and performed modeling calculation with Thermo-Calc software. The results show that high temperature tempering after normalizing is practical to 718 die steel with small cross-section.
采用TEM和ThermoCalc软件对718塑料模具钢组织中的碳化物类型及其在钢中的溶解过程进行了试验研究和模拟计算，指出正火后高温回火对小截面该钢模块具有一定的实用性。 - Feasibility of High Temperature Fast Tempering of Steel after Quenching
钢淬火后高温快速回火工艺的可行性 - After high temperature tempering the microstructure transform into tempered Sorbite.
高温回火后组织为回火索氏体。